2026 Chicago Regional Bridge Building Specifications

The object of this contest is to see who can design, construct and test the most efficient bridge within the specifications. Model bridges are intended to be simplified versions of real-world bridges, which are designed to permit a load to travel across the entire bridge. In order to simplify the model bridge design process, the number of loading positions is reduced, and to allow the contest to proceed in a reasonable amount of time, only one loading position is actually tested. These simplifications do not negate the requirement that the bridge must be designed to accept a load at any of the positions. Bridges determined by the judges to not meet this requirement will be disqualified and tested as unofficial bridges.

1. The bridge must be constructed only from 3/32 inch square cross-section basswood and any commonly available adhesive. Kits of basswood are available from the the IIT Office of Admissions, contact Margarita Fraga, fragam@illinoistech.edu, for information.
2. The basswood may be notched, cut, sanded or laminated in any manner but must still be identifiable as basswood.
3. No other materials may be used. The bridge may not be stained, painted or coated in any fashion with any foreign substance.

1. The bridge mass shall be no greater than 25.00 grams.
2. The bridge shall rest on two support surfaces separated in elevation (E) by 10. mm and horizontally by a gap (S) of 300. mm (see Figure 1).
3. The bridge (see Figure 1) must span a gap (S) of 300. mm, be no longer (L) than 400. mm, be no taller (H) than 150. mm above the lower support surface, and no wider (W) than 80. mm. No part of the bridge may extend below the lower support surface.
4. The bridge must be constructed to provide a horizontal support for the loading plate (see section 3b) at each of the three loading locations in the center of the 300. mm span and 50. mm to either side of the center (see Figure 1). The three loading locations must lie in the same horizontal loading plane a distance (P) of 10. to 50. mm above the upper support surface.

1. The load will be applied downward, from below, by means of a 40. mm square plate (see Figure 2). The plate will have a thickness (t) of at least 6 mm but less than 13 mm and will have an up to 9.53 mm (3/8 inch) diameter threaded rod attached from below at its center with a standard hex nut. The plate will be horizontal with two sides parallel to the longitudinal axis of the bridge.
2. The load will be applied on the longitudinal axis of the bridge at one of the three loading points.
3. On the day of the competition, the judges will randomly decide which of the three loading positions will be used; it will be the same for all bridges.

1. On the day of the competition, contestants will place their bridge on the testing machine support surfaces, with threaded rod projecting from below at the designated loading position.
2. The loading plate will be placed from above on the threaded rod with two sides parallel to the longitudinal axis of the bridge and secured with a hex nut.
3. The load will be applied from below, with the contestant rotating the Vernier testing machine load wheel until bridge failure is sensed (see 4d). Competition loading will stop at 50. kg.
4. Bridge failure is defined as the inability of the bridge to carry additional load as sensed by the Vernier testing machine.
5. The bridge with the highest structural efficiency, E, will be declared the winner. Bridges failing above 50. kg will be considered to have held 50. kg for efficiency calculation.

1. All construction and material requirements will be checked prior to testing. Bridges failing to meet these requirements will be disqualified. If physically possible, disqualified bridges may be tested as exhibition bridges at the discretion of the builder and the contest directors.
2. If, during testing, a condition becomes apparent (i.e., use of ineligible materials, inability to support the loading plate, bridge optimized for a single loading point, etc.) which is a violation of the rules or prevents testing as described above in Section 4, that bridge shall be disqualified.
3. Decisions of the judges are final; these rules may be revised as experience shows the need. Please check our web site, http://bridgecontest.phys.iit.edu after January 9, 2026, to learn whether any changes have been made.